#1 4 AUDIO SPLITTER DRIVER#
#1 4 AUDIO SPLITTER PRO#
#1 4 AUDIO SPLITTER PC#

#1 4 AUDIO SPLITTER PRO#

Spark! Pro series вЂ“ 1st August 2022 Spiceworks Originals.Welcome not only to Monday but the first day of August! Sometimes it feels like this year is flying by too quickly, other times that it's too slow. Snap! Raspberry Robin & Evil Corp, Linux 5.19, Tarantula Nebula, LEGO Atari 2600 Spiceworks Originals.

#1 4 AUDIO SPLITTER PC#

You can use it as an input from your mixer into your PC as well with the main or monitor outputs on the mixer depending on the model. Since you're familiar with mixers, if you're going to pick up an analog interface get a Behringer UCA-202 or 222. The point is to ONLY allow one input at a time, and to prevent that one input from sending power back to any other input source. This is also the least amount of trouble to get it to work properly.

This can be as simple as using a $12 audio switch like this, or using a stereo receiver to control the inputs.

#1 4 AUDIO SPLITTER DRIVER#

(Mic input is much lower voltage than line-in) This is the most convoluted setup because of software mixing and driver settings that may or may not work.ДЈ) Use an input switch on your speakers. There is a difference in voltage that can cause damage to the soundcard. Make sure you use the Line-In, NOT the Mic input.

this is the most expensive option, but gives you the most control.Дў) pass the echo through your soundcard's input. If you want to combine your computer and your echo to use a single speaker, you have 3 options.ДЎ) Use a mixer. (I had a fellow DJ try this with his cell phone and pc because he wanted to merge phone calls into his on-air broadcast.) It is a very good way to irreparably damage you sound card and your Echo. I spent 4 years broadcasting with a radio station in my spare time, and I can tell you with certainty - DO NOT EVER DO THIS. assuming your card has input protection, if not then you're blowing your whole card. Assuming you're dealing with 100% unamplified audio i'd actually say you're safe, but if one or both of the outputs is not line-level then you're probably going to blow input protection on your sound card. Something like this ( ) is going to give you all the inputs (just adapt the 1/4in to 1/8in) you'll ever need while it's basic and cheap is overkill in this situation.Д®lectrically yes, this does combine the line-level inputs, but as mentioned this could result in input voltage being higher than expected and 'frying' your input. ) you can then just configure your secondary Mic input to pass through to your speakers (You can do this in windows). Your 'Line In' and 'Mic' ports effectively perform the same function, with the added benefit that you can easily configure the Line In to be a passthrough leveraging your PC as an audio receiver of sorts.ДЄ Mixer would work, but you can avoid needing one by the above or purchasing a simple USB sound card (Here's one for $1.18, and it ships free. I'll bet you have all the cables do do this laying around already.This. Then the PC is the main feed of your speakers and the other device feeds to your PC as a line in device and still hits the speakers. The SPLITMix4 is designed primarily as a line level device with medium input and output impedances.There is a simple alternative, just plug the echo into the line in/mic port on your PC and make sure it's set to listen in the config. The Level attenuators cover a wide range and offer over 90dB of attenuation and channel isolation. The fully passive design of the SPLITMix4 has no active circuitry to add noise or distortion, and virtually any signal level can be handled. Stereo or mono operation is determined by the type of 1/4-inch plug and cabling that you use. Plugging into a mix input channel removes it from the splitter bus, and plugging into a splitter output channel removes it from the mix bus. All 1/4-inch connections are stereo TRS (Tip, Ring, Sleeve) and all channel connections have intelligent switching to allow for a wide variety of configurations. Independent stereo level controls are provided on each channel. You can even configure the SPLITMix4 as 4 stereo input channels thru 4 independent level attenuators to 4 stereo output channels. Mix 4 stereo input channels down to 1 stereo output, split a stereo input signal to distribute 4 stereo output channels, or combine the configurations for a wide range of applications.

The SPLITMix4 is a fully passive hybrid mixer that offers a wide variety of configurations.

1 4 audio splitter